BIO MEDICAL INCINERATOR

I    INCINERATOR
1.    Type    Air Oil Fired Incinerator
2.    Type of Waste    Medical Waste
3.    Burning Capacity    (As per 250 beds hospital Bio Wast Desposal)
4.    Auxiliary Fuel    Diesel
5.    Type of Burner Operation    Monoblock fully automatic burners
6.    Temperature

Primary Chamber Secondary Chamber    8000±500C

1050±500C
II    PRIMARY CHAMBER
1.    Type    Static Solid Hearth
2.    Material of Construction    Mild Steel, 5mm thick
3.    Refractorythickness    115mm thick
4.    Material    Refractory bricks confirming to IS-8
5.    Temperatureresistance    14000C
6.    Insulation thickness    115mm thick
7.    Material    Insulation bricks confirming to IS-2042
8.    Waste Charging    Automatic
9.    Ash Removal    Manual
III    SECONDARY  CHAMBER
1.    Type    Static Solid Hearth
2.    Material of Construction    Mild Steel, 5mm thick
3.    Refractorythickness    115mm thick
4.    Material    Refractory bricks confirming to IS-8
5.    Temperatureresistance    14000C
6.    Insulation thickness    115mm
7.    Material    Insulation bricks confirming to IS-2042
IV    EMERGENCY STACK
1.    MOC    Mild Steel, 3mm thick
2.    Refractory    75mm thick castable
3.    Insulation    25mm thick castable
V    QUENCHER
1    MOC of outer body    Mild Steel refractory lined from inside
2    Water Circulation system    Provided with centrifugal pump
3    Purpose    To reduce flue gas temperature before venturi scrubber
4    Pump motor    Suitable capacity provided as per our design
VI    AIR POLLUTION CONTROL DEVICE – VENTURI SCRUBBER
1    Type    High Pressure Jet Type
2    MOC    Stainless steel – 316L
3    Temperature at the outlet    78-800C
4    Scrubbing Media    Water with 5% caustic
VII    RE- CIRCULATION PUMP FOR VENTURI SCRUBBER
1    Type    Centrifugal
2    Application    PP/SS
3    Piping    PPR
VIII    DROPLET SEPARATOR & RE-CIRCULATION TANK (INTEGREL)
1    Type    Cyclonic
2    Application    To separate water droplets from flue gases
3    MOC    Mild Steel Rubber lined 3mm thick
IX    I.D. FAN
1    Type    High Pressure Centrifugal type
2    MOC    Stainless Steel Impeller and Mild Steel Rubber lined casting
3    Drive    Belt Driven
X    COMBUSTION FAN
1    Type    Centrifugal
2    Modulation    Manual damper control
3    MOC    Mild Steel
4    Drive    Direct drive
XI    BURNERS
1    No. of burners    2 Nos. (1 No. in Primary Chamber and 1 No. in Secondary Chamber)
2    Type    Monoblock fully automatic
3    Fuel    Diesel
XII    FUEL OIL STORAGE TANK
1    MOC & Capacity    Mild Steel, suitable capacity
2    Other Standard Accessories    Diesel Oil level indicator, piping with valves
& N.R. Valve
3    Visual checking of Fuel    To be Provided
XIII    CONTROL PANEL
1    Type    PLC based with printer & recording device having both Manual and Auto Operation
2    MOC    CRCA Sheet
3    Type of temperature controller    Digital
4    Finish & Painting type    Powder coated
5    Audio-visual alarm system    To be Provided
XIV    CHIMNEY OF 30 MTRS HEIGHT
1    MOC    Mild Steel
2    Type    Self supporting
3    Height    30 mtrs from ground level
4    Other Standard Accessories    Aviation lamp, lightening arrestor, stack, drain, inspection platform, sampling port
5    Paint    The chimney is painted externally with two coats of heat resistant aluminium paint
6    Ladder    To be Provided till the top
7    Inside Protection    3mm thick rubber lining from inside
XV    CERTIFICATION
1    Approval    PCB approved machine
2    Mandatory approvals for operation    All mandatory approvals (if any) required for the installation and operation of incinerator shall be done by the successful bidder.
XVI    TRAINING
1    Training    The successful bidder shall train the hospital staff to the satisfaction of the authorities.
XVII    TURNKEY
1.    Equipment to be installed a t s i t e a s d i re c t e d b y p r o j e c t d i r e c t o r . The civil works required to install the new machine has to be  included in the offer.

Open chat